 |
|
10-13-2008, 08:03 PM
| #1 |
| Corps Member   Join Date: Oct 2008 Location: El Paso Age: 19
Posts: 26
Credits: 3,191  | 2.2 lap is not like the 2.2 l61, lap comes in 09+ Cobalts and has VVT. Its like the 2.2 version of the LE5. (The following was provided by Maven) General Data Engine Type Inline 4 Cylinder Displacement 2.2 L 134 CID RPO LAP, LE8(E85 Compatible, HHR) Letter (VIN) F Bore 85.992-86.008 mm 3.3855-3.3861 in Stroke 94.6 mm 3.727 in Compression Ratio 10.0:1 Balance Shaft Bearing Clearance 0.030-0.060 mm 0.0012-0.0024 in Bearing Diameter - Inside - Carrier 20.050-20.063 mm 0.7894-0.7899 in Bearing Diameter - Outside - Carrier 41.975-41.995 mm 1.6526-1.6534 in Bearing Journal Diameter 20.000-20.020 mm 0.7874-0.7882 in Bushing Clearance 0.033-0.102 mm 0.0013-0.0040 in Bushing Diameter - Inside 36.776-36.825 mm 1.4479-1.4498 in Bushing Journal Diameter 36.723-36.743 mm 1.4458-1.4466 in End Play 0.050-0.300 mm 0.0020-0.0118 in Block Balance Shaft Bearing Bore Diameter - Carrier 42.000-42.016 mm 1.6535-1.6542 in Balance Shaft Bushing Bore Diameter 40.763-40.776 mm 1.6048-1.6054 in Crankshaft Main Bearing Bore Diameter 64.068-64.082 mm 2.5224-2.5229 in Cylinder Bore Diameter 85.992-86.008 mm 3.3855-3.3861 in Cylinder Bore Out-of-Round - Maximum 0.010 mm 0.0004 in Cylinder Bore Taper - Maximum 0.010 mm 0.0004 in Cylinder Head Deck Surface Flatness - Transverse 0.030 mm 0.0012 in Cylinder Head Deck Surface Flatness - Longitude 0.050 mm 0.002 in Cylinder Head Deck Surface Flatness - Overall 0.08 mm 0.0031 in Camshaft Camshaft End Play 0.040-0.144 mm 0.0016-0.0057 in Camshaft Journal Diameter 26.935-26.960 mm 1.0604-1.0614 in Camshaft Thrust Surface 21.000-21.052 mm 0.8268-0.8252 in Connecting Rod Connecting Rod Bearing Clearance 0.029-0.073 mm 0.0011-0.0029 in Connecting Rod Bore Diameter - Bearing End 52.118-52.134 mm 2.0519-2.05252 in Connecting Rod Bore Diameter - Pin End 20.007-20.017 mm 0.7877-0.7881 in Connecting Rod Side Clearance 0.070-0.370 mm 0.0028-0.0146 in Connecting Rod Straightness - Bend - Maximum 0.021 mm 0.0083 in Connecting Rod Straightness - Twist - Maximum 0.04 mm 0.0157 in Crankshaft Connecting Rod Journal Diameter 49.000-49.014 mm 1.9291-1.9297 in Crankshaft End Play 0.050-0.380 mm 0.0012-0.0150 in Crankshaft Main Bearing Clearance 0.031-0.067 mm 0.0012-0.0026 in Crankshaft Main Journal Diameter 55.994-56.008 mm 2.2045-2.2050 in Cylinder Head Overall Height, Minimum 128.9 mm 5.07 in Surface Flatness - Block Deck - Transverse 0.030 mm 0.0012 in Surface Flatness - Block Deck - Longitude 0.050 mm 0.002 in Surface Flatness - Block Deck - Overall 0.1 mm 0.004 in Valve Guide Bore - Exhaust 6.000-6.012 mm 0.2362-0.2367 in Valve Guide Bore - Intake 6.000-6.012 mm 0.2362-0.2367 in Valve Lifter Bore Diameter - Stationary Lash Adjusters 12.013-12.037 mm 0.4730-0.4739 in Lubrication System Oil Pressure - Minimum - @1000 RPM 344.75-551.60 kPa 50-80 psi Oil Capacity 4.8L 5.0 quarts Piston Rings Piston Ring End Gap - First Compression Ring 0.20-0.35 mm 0.008-0.014 in Piston Ring End Gap - Second Compression Ring 0.35-0.55 mm 0.014-0.022 in Piston Ring End Gap - Oil Control Ring - Rails 0.25-0.75 mm 0.010-0.030 in Piston Ring to Groove Clearance - First Compression Ring 0.04-0.08 mm 0.0015-0.0031 in Piston Ring to Groove Clearance - Second Compression Ring 0.030-0.069 mm 0.0012-0.0027 in Piston Ring to Groove Clearance - Oil Control Ring 0.058-0.207 mm 0.0023-0.0081 in Piston Ring Thickness - Upper First Compression Ring 1.170-1.190 mm 0.0461-0.0469 in Piston Ring Thickness - Upper Second Compression Ring 1.471-1.490 mm 0.0579-0.0587 in Piston Ring Thickness - Oil Control Ring - Rail - Maximum 0.473 mm 0.0186 in Piston Ring Thickness - Oil Control Ring - Spacer 0.929-1.006 mm 0.0366-0.0396 in Pistons and Pins Pin - Piston Pin Clearance to Connecting Rod Bore 0.007-0.020 mm 0.0003-0.0008 in Pin - Piston Pin Clearance to Piston Pin Bore 0.004-0.012 mm 0.0002-0.0005 in Pin - Piston Pin Diameter 19.997-20.000 mm 0.7873-0.7874 in Pin - Piston Pin End Play 0.210-1.266 mm 0.0083-0.0498 in Piston - Piston Diameter - @14.5 mm up 85.967-85.982 mm 3.3845-3.3851 in Piston - Piston Pin Bore Diameter 20.002-20.007 mm 0.07875-0.7877 in Piston - Piston Ring Groove Width - Top 1.23-1.25 mm 0.0484-0.0492 in Piston - Piston Ring Groove Width - Second 1.52-1.54 mm 0.0598-0.0606 in Piston - Piston Ring Groove Width - Oil Control 2.01-2.03 mm 0.0791-0.0799 in Piston - Piston To Bore Clearance, without polymer 0.010-0.041 mm 0.0004-0.0016 in Valve System Valve Lifters - Valve Lifter Diameter - Stationary Lash Adjuster 11.986-12.000 mm 0.0005-0.0020 in Valve Lifters - Valve Lifter-to-Bore Clearance - Stationary Lash Adjuster 0.013-0.051 mm 3.2210-3.2299 in Valve Springs - Valve Spring Load - Closed - @32.5 mm 245.0-271.0 N. - Eng Spec. Valve Springs - Valve Spring Load - Open - @22.5 mm 525.0-575.0 N. - Eng Spec. Valves - Valve Face Runout - Maximum 0.04 mm 0.0016 in Valves - Valve Seat Runout - Maximum 0.05 mm 0.0020 in Valves - Valve Stem Diameter - Intake 5.955-5.970 mm 0.2344-0.2355 in Valves - Valve Stem Diameter - Exhaust 5.935-5.950 mm 0.2337-0.2343 in Valves - Valve Stem to Guide Clearance - Intake 0.030-0.057 mm 0.0012-0.0022 in Valves - Valve Stem to Guide Clearance - Exhaust 0.050-0.077 mm 0.0020-0.0026 in © 2008 General Motors Corporation. All rights reserved. Last edited by ChevyRockstar; 10-16-2008 at 06:47 PM. |
| Offline |      |
|
10-16-2008, 02:05 PM
| #2 |
| Member   Join Date: Sep 2008 Location: May Landing, NJ USA
Posts: 130
Credits: 4,181 | I like how you pretty much copied and pasted my work without even giving me credit. Thanks, thats awesome.
__________________ Screws fall out all the time....the world's an imperfect place  |
| Offline | |
|
10-16-2008, 02:40 PM
| #3 | |
| Corps Member Join Date: Oct 2008 Location: El Paso Age: 19
Posts: 26
Credits: 3,191 | Quote:
__________________ | |
| Offline | |
 |
| Tags |
| 22l, lap, specs |
| Thread Tools | |
| Display Modes | |
| |
Linear Mode
