 |
|
10-26-2007, 10:41 AM
| #1 |
| ToeZup.com   Join Date: Oct 2007
Posts: 987
 | How To: Install Smoked Tailights! Pics! How to install the Modern Performance smoked taillights. Tools Needed - 3/8" Socket - 10mm deep socket - 11mm deep socket - Extension bar  The Brake Lights 1. Pop your trunk and unscrew the plastic net holders on both sides.  2. Pull the carpet back and remove the nuts from the stock lights using a 10mm deep socket.  3. Remove the stock light and unclip the harness.  4. Remove the bulb from the stock harness.  5. Insert the male harness from the new light into the same spot the stock bulb came out of and press down hard. Reconnect the harness to the car harness.  6. Insert the new light in it's place and tighten the bolts down using that 10mm deep socket. Do the same to the other side. The Reverse Lights 1. Pull the black plastic cover off the reverse lights.  2. Remove these nuts using an 11mm deep socket.  3. Remove the stock bulb from the case and pull out the stock reverse light.  4. Install the light into the new reverse light case, put the light in it's place and tighten the bolts back down.  You are now done and this is what it looks like.    
__________________  Last edited by CtCobaltSS; 10-07-2008 at 11:36 AM. |
| Offline |      |
|
10-26-2007, 05:01 PM
| #2 |
| Its Never Fast Enough  Join Date: Oct 2007 Location: Phoenix, Az.
Posts: 582
| Nice how to Ct! These are next on my list.
__________________  -GM Stage II-GMPP Catback-ZZP Header & D.P. -ZZP H.E.-K&N Typhoon-2.8 Intense Pulley -Hurst S.T.-Eibach Springs-Prothane Mounts -Ingalls Dampner-Stoptech Slotted Rotors -Hawk HPS Pads>>>>PsykoTuned<<<< |
| Offline | |
|
10-27-2007, 02:14 AM
| #3 |
| Member   Join Date: Oct 2007
Posts: 50
| Great how-to. |
| Offline | |
|
10-27-2007, 02:22 AM
| #4 |
| Junior Member Join Date: Oct 2007 Location: Corpus Christi, TX
Posts: 7
| very nice. also you can put designs in them. ill get some pics later...im tired. |
| Offline | |
|
10-27-2007, 12:55 PM
| #5 |
| ToeZup.com Join Date: Oct 2007
Posts: 987
| Thanks guys. I really like the lights. Post pics when you install those KevinsSSSC. They would look sick on orange.
__________________ |
| Offline | |
|
11-19-2007, 12:13 AM
| #6 |
| MECP Certified  Join Date: Oct 2007 Location: CT Age: 21
Posts: 768
| looks good man. |
| Offline | |
|
11-19-2007, 09:59 AM
| #7 |
| ToeZup.com Join Date: Oct 2007
Posts: 987
| Thank you sir.
__________________ |
| Offline | |
|
11-20-2007, 08:09 PM
| #8 |
| Member  Join Date: Nov 2007
Posts: 268
| very nice job. i got some smoked taillights a few weeks back. not the same ones. but mine were so hard to instal. the reverse lights those nuts wouldnt fit i had to drive to hardwear store to get smaller size
__________________  |
| Offline | |
|
10-06-2008, 06:15 PM
| #9 |
| CUSTOMIZER   Join Date: Jan 2008 Location: White Bear Lake, Minnesota Age: 23
Posts: 1,494
| Great how to Tony! Is that a Raptor front clip I see in the back ground of the last pic?
__________________  |
| Online! | |
|
10-06-2008, 08:46 PM
| #10 |
| Member  Join Date: Sep 2008 Location: May Landing, NJ USA
Posts: 120
| Those look good man, Ive been looking for lights with a nice clean look like that, because I didnt want to resort to building my own. Who are they from? What is it with you guys and 3/8" drive. LOL All you need is 1/4" |
| Offline | |
 |
| Tags |
| install, pics, smoked, tailights |
| Thread Tools | |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| LED Tailights | KevinsSSSC | Appearance | 10 | 03-14-2008 10:47 PM |
Linear Mode
